Note: Image Shows Black Relocation Kit. Actual Kit Is ChromeTwo types of turn signal relocation kits available: universal kit moves rear turn signals to the license plate mount and specific-fit kits relocate stock turn signals further back by extending the chrome fender rail (read more)

Turn Signal Relocation Kit Needed When saddlebags are installed (read more)

Mount auxiliary marker lights or turn signals to your license plate and open up that saddlebag area or just streamline your rear fender. This simple system mounts directly to the back of your license plate with support backing plate and two side mount brackets. The side mount brackets have a 38 hole… (read more)

Fits all Metric Cruisers. (read more)

…relocates the license plate while bringing it closer to the rear fender and relocates the rear turn signals. The final result is a lightweight clean and uncluttered rear fender look. Other features include: Powder-coated metal constructionHigh-strength design with a durable finishTurn signals relocate… (read more)

Chrome plated 90 steel bracketsGreat for installing auxiliary lights or turn signal lights almost anywhereSold in pairs (read more)

Turn signals are a necessity its true but they can clash with the bikes look and get in the way of saddlebags. Cobras fix is a Rear Turn Signal Kit that relocate the indicators by replacing the long plastic stalks with shorter mounts. (read more)

Each License Plate Illuminator has two L.E.D.s. The white L.E.D. lights up the license plate the rear-facing red L.E.D. can function as an auxiliary running light turn signal or brake light for added visibility. The 14- 20 mounting stud makes it simple to bolt them on wire them in ride on (read more)

…not only unsafe its illegal and leaves you likely to get pulled over by police. This license plate mount will provide additional tail brake and turn signal lights as well as a license plate light and mounting location. The LED lights are extremely bright even in direct sunlight and both water and vibration… (read more)

…allow you to replace your large stock rear turn signals with these streamlined bullet shaped turn signals and relocate your license plate below the taillight. There is a built-in light to illuminate the relocated license plate. The bullet shaped turn signals are single circuit and come equipped with… (read more)

…Now you can mount a set of Edge Saddlebags and keep your stock turn signals. This kit takes all the guess work out of relocating your stock signals by moving them from the fender to the license plate area.Does not include turn signals (read more)

Raised License Plate Holder with amber or red LED Turn Signal Lights. When replacing incandescent turn signals with LEDs a Dual Load Equalizer is required 13-304A. Fits standard 7 x 4 motorcycle plates. This works as a running and brake light on the plate itself. (read more)

Constructed of 14 gauge steel. This rigid bracket is laser cut and formed. The finish is Black Powder Coat that looks great and is very tough. Relocates rear turn signals further back for use when putting on saddlebags. - Honda Shadow VLX 600- Honda Shadow Spirit 1100 (read more)

…allow you to replace your large stock rear turn signals with these streamlined bullet shaped turn signals and relocate your license plate below the taillight. There is a built-in light to illuminate the relocated license plate. The bullet shaped turn signals are single circuit and come equipped with… (read more)

3 in 1 FeatureSequential Turn SignalRight and Left LED arrays indicate sequential turn signals. These superbright LEDs 8500 mCd have a wide viewing angle of 180 degrees. They are sunlight readable even from the adjacent lanes. Brake Light ModulatorA cluster 6 LEDs is magnified by an acrylic lens to broadcast… (read more)

Replace your large stock rear turn signals with these streamlined bullet shaped turn signals relocate your license plate below the taillight. Built-in light illuminates the relocated license plate. Single circuit turn signals come equipped with our stylish deep-dish bezels with red lenses. A flat license… (read more)

…attach to the front hole in the fender rail and the rear hole on the fender rail. This model is the standard Easy Bracket depth. This model may be used if a smaller saddlebag is used and located behind the rear shock. Turn signals must be relocated off the fender on all Sporster models. (read more)

Slick Signal License Plate Frame and Turn Signals feature LED two-function lights. Can be wired up as run and brake or run and turn. Fits 4 inch x 7 inch license plates. Made from aluminum and polished and chrome plated. Not D.O.T approved. For custom applications (read more)

This bracket will move the license plate up 2 to show off that wide rear tire and bring the turn signals in 3 closer to the fender on each side for a clean custom look. (read more)

…your rear wheel for that fat-tire look by replacing your plastic sub-fender license and turn signal assembly with our rear license mount for the Yamaha V-Star 1100. The Unit is finished in bright chrome. Reuses stock brake light. Turn signal flange mounts allow for the use of most aftermarket signal lights… (read more)

…quickly and easily.- Streamlined recessed mounts allow you to use custom indicator lights like our Bullet Marker Lights or you can reuse your stock turn signals as shown.Please Note: BA-3400-00 Bullet Marker Lights sold separately (read more)

…IntensityRunningBrake or Brake Only LEDs 20 Super Bright Amber Turn Signal LED Per SideFrame dimensions: 7-316 length x 4-14 widthMounting holes center to center: 5-34 x 2-1316Mounting Hardware IncludedLifetime Warranty Black Horizontal Die-Cast With Amber Turns (read more)

…IntensityRunningBrake or Brake Only LEDs 20 Super Bright Amber Turn Signal LED Per SideFrame dimensions: 7-316 length x 4-14 widthMounting holes center to center: 5-34 x 2-1316Mounting Hardware IncludedLifetime Warranty Black Horizontal Die-Cast With Amber Turns (read more)

…features of the NessRWD assemblies and more. Made in the USA and beautifully chrome plated.Features:This license frame also includes DOT approved LED turn signalsbrake lights for the ultimate in safety and styleCan be used on any custom application or any RWD recessed mounting pockets listed elswhereMachined… (read more)

This bracket relocates the Kawasaki VN2000 license plate to under the rear turn signals for a clean and custom look. Required for mounting Sissy Bar Luggage Rack BBP-55-322 to Sissy Bar Kit BBP-71-130. (read more)

Check out our new M109 Side mount Tag Mount. Locates under the rear fender for a new clean look Designed to be used with the Kewlmetal Item 153 Bullet Turn Signal Mount Brackets. (read more)

Note: Image Shows Chrome Relocation Kit. Actual Kit Is BlackTwo types of turn signal relocation kits available: universal kit moves rear turn signals to the license plate mount and specific-fit kits relocate stock turn signals further back by extending the chrome fender railNote: May Not Fit with All… (read more)

Note: Image Shows Chrome Relocation Kit. Actual Kit Is BlackTwo types of turn signal relocation kits available: universal kit moves rear turn signals to the license plate mount and specific-fit kits relocate stock turn signals further back by extending the chrome fender railNote: May Not Fit with All… (read more)

Note: Image Shows Chrome Relocation Kit. Actual Kit Is BlackTwo types of turn signal relocation kits available: universal kit moves rear turn signals to the license plate mount and specific-fit kits relocate stock turn signals further back by extending the chrome fender railNote: May Not Fit with All… (read more)

Two types of turn signal relocation kits available: universal kit moves rear turn signals to the license plate mount and specific-fit kits relocate stock turn signals further back by extending the chrome fender railNote: May Not Fit with All Styles of Sissy Bar Side Plates (read more)

Two types of turn signal relocation kits available: universal kit moves rear turn signals to the license plate mount and specific-fit kits relocate stock turn signals further back by extending the chrome fender railNote: May Not Fit with All Styles of Sissy Bar Side Plates (read more)

Two types of turn signal relocation kits available: universal kit moves rear turn signals to the license plate mount and specific-fit kits relocate stock turn signals further back by extending the chrome fender railNote: May Not Fit with All Styles of Sissy Bar Side Plates (read more)